Design reference photoCreator photo; included parts are listed below. Accessories not included.
Reusable Wet Wipes Pack Lid — V4
3D printed in PETG for adding a reusable closure to a compatible wipes pack.
Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.
Check fit before ordering ↓A closer look
3D printed in PETG for adding a reusable closure to a compatible wipes pack. Includes one V4 printed lid assembly. Hardware, devices, accessories shown and installation are not included.
Check the fit
Start with these details so you can choose the right part for your setup.
- Review the listed design, size and included quantity before ordering.
What’s included
- One V4 printed lid assembly.
- Hardware, devices, accessories shown and installation are not included.
Give a compatible wipes pack a reusable closure
A reusable lid is useful when you want a defined opening and closing routine for a compatible flexible wipes pack. Place the pack where it can stay supported while a wipe is removed, such as a convenient shelf or care station, and orient the lid so it opens into free space. The V4 design provides the printed lid assembly for that arrangement. Its usefulness depends on a good match with the pack opening and on an attachment that suits the pack material, so compare the actual pack before planning to reuse it across several brands.
Measure the opening and the surrounding flat area
The assembly's approximate 68.15 × 114.31 × 8 mm measurements are its individual bounding dimensions. They do not specify the size of the dispensing opening or the attachment area required on the packaging. Check the existing pack opening, any raised seam and the available flat material around it. Consider how the pack changes shape as it empties: a fit that seems convenient on a full pack may be less stable when the packaging folds. Leave clearance for the lid's opening motion and for your fingers to reach the wipes.
Plan fitting and daily use together
Trial-position the lid before using any separately chosen attachment method. It should sit without stretching the packaging or obstructing the opening needed to pull a wipe through. Follow the wipes supplier's instructions for storage and use, and close the lid after dispensing. This listing does not state an airtight seal or a guaranteed moisture-retention result, so monitor the actual pack rather than assuming the printed closure replaces every feature of the original packaging. Keep the pack supported during use so the repeated pulling motion is not carried only by the lid attachment.
Clean before moving it to another pack
Inspect the lid and its moving or mating surfaces for residue that might prevent full closure. Clean it using a gentle method compatible with the intended use, then let it dry before refitting. If transferring it to a new pack, remove remnants of the previous attachment and check the new pack's opening again. Reusability does not imply that every replacement pack has the same shape. Avoid forcing the closure if the packaging has folded into it, and replace the part if a hinge, edge or closing feature becomes cracked or unreliable.
Product questions
What does the listed price include?
One V4 printed lid assembly. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Hardware, devices, accessories shown and installation are not included.
Will this match everything shown in the photo?
The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.
Will this keep every wipes pack airtight?
No airtight or moisture-retention performance is stated. Fit and closure depend on the actual pack and attachment, so follow the wipes supplier's storage guidance and check the result.
Can I transfer the lid between brands?
Only after comparing each pack's opening, seams and attachment area. Similar-looking packs can have different opening shapes or flexible packaging that behaves differently.
What should I check as the pack empties?
Make sure folded packaging is not trapped in the closure and that the attachment remains secure. Support the pack while dispensing so the lid is not taking the entire pulling force.
Original design: NicoM1989 — Wet Wipes Lid - Update V4.0. MakerWorld model 500995. Original design