Creator design reference for 18650 TP4056 Project Housing — Single Bay; included printed parts are specified in the listing.Design reference photo

Creator photo; included parts are listed below. Accessories not included.

Electronics & racks / Parts for your next project

18650 TP4056 Project Housing — Single Bay

3D printed in PETG for housing separately supplied single-cell charging components.

$27.99 CAD

Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.

Check fit before ordering ↓

A closer look

3D printed in PETG for housing separately supplied single-cell charging components. Includes one single-bay printed housing. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included. Printed housing only; no electrical function is supplied.

Check the fit

Start with these details so you can choose the right part for your setup.

  • Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.

What’s included

  • One single-bay printed housing.
  • Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.

Organize the physical side of a single-cell project

This housing is intended for a project built around separately supplied single-cell charging components. It gives the project a defined printed form while leaving the electronics, cell selection and electrical design to the builder. Think through how the cell, contacts, charging board and connected cable will work together before fitting the parts. A useful layout keeps the charging connection accessible and makes it possible to inspect the cell arrangement later. The product name describes the intended project family; the printed housing itself neither charges a cell nor provides a protection circuit.

Check the complete cell and board combination

The approximate 98.77 × 23.24 × 20 mm dimensions are the outside bounding measurements of the printed part. They do not specify the usable bay size or establish compatibility with every item sold as an 18650 cell or TP4056 board. Compare the actual cell, any protection or terminal features, contacts and wiring allowance. Charging modules can also differ in connector type, connector location and board outline. Include the attached charging plug in the check, because a board that sits inside the housing may still be awkward to connect when the project is assembled.

Trial-fit without relying on pressure

Work with the cell removed and the charging connection disconnected while checking the mechanical layout. The intended components should locate without force being used to bend the board or squeeze the cell into a space that is too small. Plan suitable electrical insulation and contact retention independently; the housing should not become a reason to leave exposed connections where they can move or touch. Follow the chosen components' instructions for cell compatibility, charging and protection. Make sure maintenance access does not require pulling directly on wires or prying against battery terminals.

Keep the project inspectable

Before use, check that the charging cable can connect and disconnect cleanly and that its normal movement does not shift the internal assembly. Recheck the fit whenever a cell, contact or charging board is changed. No sealing, thermal or fire-containment rating is stated, so select the project location and electrical provisions according to the actual electronics rather than the appearance of the enclosure. Keep the printed part free of loose debris and inspect it for distortion or cracks. Clean it only with the electrical components safely disconnected and let it dry fully before reassembly.

Product questions

What does the listed price include?

One single-bay printed housing. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.

Will this match everything shown in the photo?

The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.

Does TP4056 in the name mean a charging board is fitted?

No. The supplied item is a printed housing. The charging board, cell, contacts and any protection circuitry are separate parts that must be selected and integrated appropriately.

Will a longer protected 18650 cell fit?

That is not established by the listing. Compare the actual cell's full dimensions, its terminal shape and the space needed by the chosen contacts before ordering.

Can I treat the housing as a ready-to-use charger?

No. It has no electrical function on its own. A working charger depends on the correct components, wiring, cell compatibility and verification of the completed project.

Original design: Gerry di STL 3D Italia — Box con modulo TP4056 per ricarica batterie 18650. MakerWorld model 2937443. Original design

Your cart

Ordering within Canada? Buy each product through its secure checkout, or ask us about combining parts into one order.

Your cart is empty. Find a useful part and add it here.