Design reference photoCreator photo; included parts are listed below. Accessories not included.
ESP32 and 18650 Project Box
3D printed in PETG for housing separately supplied controller and battery components.
Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.
Check fit before ordering ↓A closer look
3D printed in PETG for housing separately supplied controller and battery components. Includes one printed box body and one matching lid. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included. Printed housing only; no electrical function is supplied.
Check the fit
Start with these details so you can choose the right part for your setup.
- Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.
What’s included
- One printed box body and one matching lid.
- Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Plan a compact controller project as a complete assembly
This box provides a physical housing for separately chosen ESP32 and 18650 project components. It can help bring a prototype's board, battery arrangement and wiring into one planned layout once you have established how the electronics will work. Decide what the project needs to expose before fitting anything: a programming connection, a control, a charging connection or a cable leaving the enclosure can all affect the layout. The printed body and lid organize space; they do not supply charging, battery protection, power conversion or any other electrical function.
Measure the electronics with their connections
ESP32 boards come in different shapes and connector arrangements, and a cell's final occupied space depends on its holder, contacts and wiring. Compare those complete assemblies, including protruding components and the room needed to remove plugs. The body is approximately 72 × 84 × 28 mm and the lid is approximately 72 × 84 × 2 mm as individual printed parts. Those outside measurements are not the usable internal cavity. Leave room for wire routing and closure features rather than planning components right up to the outer dimensions.
Dry-fit before making the electrical assembly permanent
Start with the project unpowered and arrange the components without forcing them into place. Confirm that the lid can close without pressing on the board, squeezing the cell or pinching wires. Keep any cell terminals and conductive parts appropriately separated through the actual electrical design, and use the component manufacturers' requirements for battery selection and charging. Plan how you will access the battery and programming connection later. A useful enclosure layout allows maintenance without pulling on solder joints or lifting the board by a connected cable.
Review the housing when the project changes
A new board revision, larger plug or replacement battery holder can change the fit even when the project name stays the same. Repeat the clearance check after any component swap and keep cables from bearing against the lid seam. No sealing, fire containment or thermal performance rating is specified for this housing; choose its location and electrical design on that basis. Remove loose dust with the electronics disconnected and keep moisture away from the assembled project. If the body or lid distorts or develops cracks, inspect the internal arrangement before continued use.
Product questions
What does the listed price include?
One printed box body and one matching lid. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Will this match everything shown in the photo?
The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.
Does the enclosure charge or protect an 18650 cell?
No. It is a printed body and lid. Charging, protection, contacts and all other electrical functions depend on the separately supplied components and their correct integration.
Can I use the listed dimensions as internal board clearance?
No. They are approximate individual part dimensions. Internal walls, closing features, wiring and connectors reduce or change the usable space and require a separate fit check.
Should I fit the box before or after wiring the project?
Plan and trial-fit the unpowered components first, including the cable routes. This helps identify lid interference and maintenance access before you commit to the final wiring.
Original design: Arvixs — ESP32 POWER BOX 18650. MakerWorld model 2790135. Original design