Creator design reference for Ethernet Twisted-Pair Untwisting Pick; included printed parts are specified in the listing.Design reference photo

Creator photo; included parts are listed below. Accessories not included.

Electronics & racks / Parts for your next project

Ethernet Twisted-Pair Untwisting Pick

3D printed in PETG for separating cable pairs during manual cable preparation.

$27.99 CAD

Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.

Check fit before ordering ↓

A closer look

3D printed in PETG for separating cable pairs during manual cable preparation. Includes one PETG printed untwisting pick. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.

Check the fit

Start with these details so you can choose the right part for your setup.

  • Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.

What’s included

  • One PETG printed untwisting pick.
  • Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.

A hand tool for the cable preparation stage

This pick is intended for the manual step of separating twisted cable pairs while preparing a cable end. It can give your fingers a more defined point of contact when working through the exposed pairs before arranging the conductors for a termination. Keep it beside the tools already used for stripping, trimming and terminating, so cable preparation follows a consistent sequence. It does not cut the jacket, terminate a connector or test a finished link. Those jobs still need the appropriate tools and checks for the cable and connector system you are using.

Match the technique to the cable

Cable constructions differ in conductor size, insulation, separators and shields. Start on a spare offcut of the same cable to understand how the pick enters the pair and how much hand pressure is needed. Work progressively near the exposed end rather than trying to pull a long twisted section apart in one movement. Preserve the twist arrangement as far as the termination method requires, following the cable and connector supplier's instructions. The goal is controlled preparation of the required exposed length, with the insulation and conductor shape left intact.

Set up a manageable bench workflow

Allow enough cable length on the bench that its own weight does not pull against the section you are working on. Hold the cable securely without crushing the jacket, separate the pairs deliberately, and keep the conductor order visible as you move to the next step. The pick's approximate 148.83 × 9.9 × 13.99 mm component size helps when planning a tool pouch or bench tray. It does not define a compatible cable diameter. Make a practice termination before preparing a large batch, particularly if the cable is unfamiliar or has a different internal layout.

Look after the tip and inspect the result

Use the printed pick with gentle hand pressure; it is not a lever for opening hardware or a probe for powered equipment. Inspect the contact area before use and stop if it becomes damaged or leaves marks on cable insulation. Brush away fragments of jacket or filler so the working surface remains visible. After preparing a cable, examine the insulation and complete the termination and testing process appropriate to the installation. A tidy-looking cable end is useful, but appearance alone cannot establish that a finished network connection has been wired or terminated correctly.

Product questions

What does the listed price include?

One PETG printed untwisting pick. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.

Will this match everything shown in the photo?

The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.

Does this tool replace a cable stripper or crimper?

No. It assists with separating pairs during preparation. Jacket removal, connector termination and finished-cable testing remain separate operations requiring suitable tools.

Is a particular Ethernet cable category guaranteed?

No category-specific compatibility is stated. Compare the cable construction and practise on an offcut, using the termination requirements supplied with your chosen cable and connector.

How can I avoid damaging conductor insulation?

Use small, controlled movements and inspect the contact area frequently. Stop if the tip catches, scratches or requires force, and adjust your technique before continuing.

Original design: @Beast-Lab — RJ45 Cat5 Cable Untwist Tool for Faster Crimping. MakerWorld model 2767390. Original design

Your cart

Ordering within Canada? Buy each product through its secure checkout, or ask us about combining parts into one order.

Your cart is empty. Find a useful part and add it here.