Design reference photoCreator photo; included parts are listed below. Accessories not included.
Flexible Conduit Connector — 16 mm to M16
3D printed in PETG for joining compatible flexible conduit to a project enclosure fitting.
Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.
Check fit before ordering ↓A closer look
3D printed in PETG for joining compatible flexible conduit to a project enclosure fitting. Includes one V2 connector in the 16 mm conduit to M16 × 1.5 configuration. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Check the fit
Start with these details so you can choose the right part for your setup.
- Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.
What’s included
- One V2 connector in the 16 mm conduit to M16 × 1.5 configuration.
- Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Connect the conduit route to the enclosure layout
This V2 connector is intended for a compatible 16 mm flexible conduit and an M16 × 1.5 enclosure fitting arrangement. It is useful when a project needs a deliberate transition between a conduit run and a box, rather than leaving the conduit end loose beside an opening. Start by planning the direction from which the conduit approaches. A fitting can match both interfaces yet still be awkward if the conduit must turn sharply immediately beside it. Leave access to the connector after the enclosure is installed so the route can be inspected or adjusted. The part serves the stated mechanical connection; any requirements for the wiring or completed enclosure must be assessed separately.
Confirm both sides of the connection
Check the actual conduit profile as well as its nominal 16 mm size, since the outer shape and corrugations affect how a printed connector engages. On the enclosure side, verify the M16 × 1.5 configuration and the mating fitting or opening arrangement. Thread size and pitch both matter; a similar-looking thread is not enough to establish compatibility. The approximate 24.78 × 22 × 26.5 mm printed-part dimensions are bounding measurements, not a drilling template or an internal cable clearance specification. Include enclosure wall thickness, tool access, and any required separately selected retention pieces in the fit check. Confirm the details before cutting an opening or planning a tightly packed row of fittings.
Fit without forcing the printed interfaces
Trial-fit the connector and conduit with the project unpowered. Align threaded parts carefully and stop if they bind instead of seating naturally; forcing a mismatched thread can damage both the connector and the mating part. Route the conduit so its weight or movement does not continually lever against the enclosure entry. Check that the cable path is clear and that no edge pinches a jacket when the conduit is moved through its expected range. The PETG connector does not establish a weather seal, certified strain relief, or an electrical installation approval. During routine inspection, look for looseness or distortion at both interfaces, particularly after the enclosure or conduit route has been repositioned.
Product questions
What does the listed price include?
One V2 connector in the 16 mm conduit to M16 × 1.5 configuration. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Will this match everything shown in the photo?
The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.
Will every conduit sold as 16 mm fit?
Confirm the actual profile and dimensions of your conduit. Nominal size alone does not describe the shape that engages the connector, so a close-up photo and measured outside size are useful for a fit check.
Is M16 enough information to match a fitting?
No. This version is identified as M16 × 1.5, so both size and pitch need to match. Also check the mating geometry and the space available around the enclosure entry.
Does the connector make an enclosure waterproof?
No sealing rating is specified. A mechanical conduit connection does not by itself establish environmental protection for an enclosure; seals, openings, and the complete installation need to be considered separately.
Original design: jikulec — Flexible Pipe to Cable Gland Connector. MakerWorld model 1928464. Original design