Design reference photoCreator photo; included parts are listed below. Accessories not included. The photo shows an assembled project; this listing includes only the specified printed components.
10-inch 5U Rack Panel Pack — Circle Hex
3D printed in PETG for building or repairing a compatible Circle Hex rack enclosure.
Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.
Check fit before ordering ↓A closer look
3D printed in PETG for building or repairing a compatible Circle Hex rack enclosure. Includes five Circle Hex printed panels; additional repeated panels and hardware excluded. Hardware, devices, accessories shown and installation are not included.
Check the fit
Start with these details so you can choose the right part for your setup.
- Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.
What’s included
- Five Circle Hex printed panels; additional repeated panels and hardware excluded.
- Hardware, devices, accessories shown and installation are not included.
Plan the panel pack as part of a complete rack
This Circle Hex panel pack is intended for building or repairing a compatible 10-inch 5U rack enclosure. Begin with an inventory of the enclosure you have or intend to assemble, then identify which positions the five printed panels will occupy. This is particularly useful for a repair, where some original panels or structural parts may still be usable. Confirm the arrangement before ordering so the supplied group can be matched to the actual missing pieces. A rack enclosure involves more than its outer panels: equipment mounting, assembly hardware, and any repeated panels need their own plan. Treat the five-piece pack as a defined set of printed components for that broader build.
Check interfaces before relying on the rack name
The 10-inch 5U description identifies the intended enclosure format, but fit still depends on the Circle Hex arrangement and the parts you are combining. Compare panel edges, joining features, fixing points, and the positions of any existing rails or supports. The five component measurements range from thin panels to deeper shaped pieces; these are individual bounding sizes, not the assembled enclosure dimensions. Do not infer the usable equipment depth or internal volume by adding them together. Check the devices and connected plugs as a complete layout, allowing room for cable bends and access. If repairing an enclosure, photos of the damaged area and the adjoining pieces are useful for confirming the intended panel match.
Assemble with equipment access in mind
Trial-position the panels before tightening an assembly, and confirm the required separately supplied hardware against the actual joining features. Check that edges meet naturally without using excessive force to pull a misaligned arrangement together. Place equipment only after its independent mounting and support requirements have been resolved. Leave access to ports, controls, and ventilation areas specified by the equipment manufacturers. The PETG printed panels do not establish an equipment load rating or an environmental enclosure rating. For maintenance, keep track of which panels need removal to reach a particular device and avoid burying service fasteners behind cable bundles. Recheck alignment after a rack move or a significant equipment change, since cable pressure can make a previously clear interior difficult to service.
Product questions
What does the listed price include?
Five Circle Hex printed panels; additional repeated panels and hardware excluded. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Hardware, devices, accessories shown and installation are not included.
Will this match everything shown in the photo?
The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.
Is this a complete ready-to-load rack?
The listing supplies five printed Circle Hex panels and excludes additional repeated panels and hardware. Review the full enclosure arrangement and equipment mounting requirements to determine what else your particular build needs.
Will these panels fit another 10-inch rack design?
Not on the rack-format name alone. Compare the joining geometry, fastener positions, and panel edges. The pack is intended for the compatible Circle Hex enclosure arrangement described in the listing.
Can I determine usable depth from the largest panel?
No. Panel dimensions describe separate parts and do not establish assembled internal clearance. Include the joining arrangement, equipment depth, connected plugs, and cable bends when checking the finished rack layout.
Original design: Tech_Luke — 10″ Rack Enclosure (5U) – Modular & Wall-Mountable. MakerWorld model 1913011. Original design