Design reference photoCreator photo; included parts are listed below. Accessories not included.
21700 Battery Pack Housing — Four Cell
3D printed in PETG for holding components of a custom four-cell battery project.
Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.
Check fit before ordering ↓A closer look
3D printed in PETG for holding components of a custom four-cell battery project. Includes one four-cell housing: bottom, spacer and top. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included. Printed housing only; no electrical function is supplied.
Check the fit
Start with these details so you can choose the right part for your setup.
- Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.
What’s included
- One four-cell housing: bottom, spacer and top.
- Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Use the housing to develop the mechanical layout
This four-cell housing is intended for a custom project using compatible 21700 cells. Its bottom, spacer, and top provide physical parts around which the rest of the assembly can be planned. Begin by considering where the completed project will sit, how it will be accessed, and what must remain visible for inspection. A housing that is convenient on an open bench may become difficult to service once placed inside another enclosure. Lay out the printed pieces before deciding where wiring and other components belong. Treat the housing as one element of the mechanical design: it does not supply the electrical connections, protection, or charging system that a completed battery project may require.
Check the actual cells and completed assembly
The 21700 designation is a starting point for checking cell size, not a guarantee that every cell sold under that description has identical end details or fits every arrangement. Compare the specific cells, including their ends and wrappers, with the housing geometry. The listed dimensions describe three separate printed parts and must not be added together to infer a finished pack size. Account for how the bottom, spacer, and top overlap, as well as the separately supplied contacts, wiring, and any additional project components. Confirm the space needed for assembly and inspection before designing a tight outer case. Nothing should rely on the printed lid pressing hard against cells to compensate for an unresolved fit.
Assemble and inspect as a housing project
Plan mechanical fitting while cells are removed and keep loose conductive pieces out of the working area. Check that the printed parts meet naturally and that any chosen retention method does not crush wiring or damage cell wrappers. The PETG housing does not establish a voltage, current rating, charging method, or protective enclosure rating. Follow the requirements of the cells and electrical components in your project, and resolve those requirements before treating the assembly as a usable pack. For ongoing inspection, keep the housing accessible and check it after impact, movement, or changes to the internal arrangement. A distorted part, trapped wire, or damaged cell wrapper calls for correction before the assembly is used again.
Product questions
What does the listed price include?
One four-cell housing: bottom, spacer and top. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Will this match everything shown in the photo?
The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.
Does the four-cell arrangement specify series or parallel wiring?
No. The printed housing does not connect the cells or define a circuit. The number of positions describes the mechanical project scope; electrical configuration and protection must be established separately for the selected components.
Can I infer the pack height from the three part measurements?
No. These are individual component bounding dimensions, and parts may overlap when assembled. Confirm the completed arrangement with the intended cells and other components before setting an outer enclosure size.
Is the spacer an electrical protection component?
It is described as a printed housing component. Do not infer an electrical protection, insulation certification, or cell-management function from its presence. The completed project needs its own appropriate electrical design and verification.
Original design: wrong17 — Li-ion 21700 Battery Pack Case Holder 6s 4s & 3s. MakerWorld model 1791661. Original design