Creator design reference for Four-Cable Holder — 6 mm Cable Design; included printed parts are specified in the listing.Design reference photo

Creator photo; included parts are listed below. Accessories not included.

Home organization / Practical pieces for your home

Four-Cable Holder — 6 mm Cable Design

3D printed in PETG for keeping four compatible cables in place.

$27.99 CAD

Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.

Check fit before ordering ↓

A closer look

3D printed in PETG for keeping four compatible cables in place. Includes one holder for four nominal 6 mm cables. Hardware, devices, accessories shown and installation are not included.

Check the fit

Start with these details so you can choose the right part for your setup.

  • Compare the opening, cable, shelf or mounting area with the listed design and dimensions.

What’s included

  • One holder for four nominal 6 mm cables.
  • Hardware, devices, accessories shown and installation are not included.

Assign a place to four everyday cables

This holder is useful where several compatible cables meet the same work area and tend to fall behind the desk or drift into each other. Decide which four cables belong together before fixing the holder in place. A useful grouping might follow a workstation activity, with the leads you reach for together arranged in a consistent order. The holder can then become a return point after disconnecting a device, making the next connection easier to find. Plan the position around the cable ends you handle, rather than placing it only where the empty holder looks neat. A short trial arrangement on the desk can reveal whether the cables need different exit directions.

Measure the jacket at the holding point

The nominal 6 mm cable design refers to the intended cable size, not to the connector at the end of the lead. Measure the outer jacket where it will sit in the holder and compare how firm or flexible that jacket feels. Flat, braided, unusually soft, or irregular cables may behave differently from a round cable of similar width. The printed part is approximately 53.9 × 15.14 × 15 mm overall; those measurements do not establish a precise gripping clearance for every lead. Check each cable individually and avoid forcing a larger one into place. Also allow room for connector housings and normal cable movement beside the holder.

Leave slack for the way devices move

Route each cable so the holder organizes its position without becoming the point that takes every pull from a moving device. Leave a practical service loop for lifting a phone, moving a laptop, or reaching the back of equipment. Check the route with drawers open and chairs or monitor arms in their normal positions. The PETG holder should not pinch the jacket or force a tight bend immediately beside a plug. Confirm how the holder will attach to your chosen surface before installation, since the surface and fastening method affect the result. During cleaning, lift dust from around the cable seats and inspect jackets for rubbing. Revisit the arrangement when equipment changes, because a tidy route for one lead may be too short for its replacement.

Product questions

What does the listed price include?

One holder for four nominal 6 mm cables. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Hardware, devices, accessories shown and installation are not included.

Will this match everything shown in the photo?

The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.

Can it hold thinner cables as well?

Thinner cables may sit loosely, depending on their jacket and the holder geometry. Confirm the fit of your actual leads instead of assuming that all cables below 6 mm will stay in the same position.

Should I bundle all four cables together first?

Check the intended individual cable seats before adding any bundle wrap. A wrap changes the effective size and may prevent the cables from seating. Keeping each lead identifiable also makes later changes easier.

Where should I position it on a desk?

Choose a reachable location with enough slack between the holder and each device. Test your normal unplugging and lifting movements first, then check that the cable ends remain accessible when devices are absent.

Original design: Pitshaft — Cable Holder. MakerWorld model 1664195. Original design

Your cart

Ordering within Canada? Buy each product through its secure checkout, or ask us about combining parts into one order.

Your cart is empty. Find a useful part and add it here.