Creator design reference for AA Battery Holder — Four Cell; included printed parts are specified in the listing.Design reference photo

Creator photo; included parts are listed below. Accessories not included.

Electronics & racks / Parts for your next project

AA Battery Holder — Four Cell

3D printed in PETG for positioning four AA cells in a project.

$29.99 CAD

Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.

Check fit before ordering ↓

A closer look

3D printed in PETG for positioning four AA cells in a project. Includes one printed four-cell AA battery holder. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included. Printed housing only; no electrical function is supplied.

Check the fit

Start with these details so you can choose the right part for your setup.

  • Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.

What’s included

  • One printed four-cell AA battery holder.
  • Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.

Plan the cell location before the circuit layout

A four-cell AA holder can help establish a clear mechanical location for cells in a custom project. Start by deciding how often the cells will need to be removed and from which direction you want to reach them. That choice influences where the holder belongs inside the enclosure and where surrounding boards or wiring can go. Keep the cell area easy to inspect, especially if the finished project will otherwise hide it behind a panel. This printed part provides the physical holder described in the listing. It does not establish an electrical connection between cells, so your circuit layout should be planned separately from the convenient four-cell arrangement.

Allow for contacts as well as the cells

The approximate 76 × 62 × 14 mm measurements describe the printed holder overall. They do not define the clearance needed for a completed assembly with cells, metal contacts, wires, and access for replacement. Compare the actual AA cells and your proposed contact arrangement with the holder before designing a tightly fitted enclosure around it. Consider both ends of every cell and the space needed to remove a cell without prying against nearby electronics. If your design uses a lid, leave room for that lid to close without pressing on cells or terminals. A mechanical trial layout is especially helpful when wires must pass beside the holder or through a narrow enclosure opening.

Keep the printed holder and electrical design distinct

The PETG part is a housing component, so the completed project still needs an appropriate approach to contacts, polarity marking, wiring, and electrical protection. Work on the mechanical assembly with the cells removed. Check that fitted contacts cannot move into an unintended position and that wiring is not trapped between a cell and the printed wall. Follow the instructions for the cells and electronics you choose, rather than inferring a voltage or charging method from the number of positions. For routine care, inspect the holder whenever cells are replaced and remove loose debris before reloading it. Stop using the arrangement if the shell, contacts, or cell wrappers show damage; replacing a compromised part is preferable to forcing the cells into place.

Product questions

What does the listed price include?

One printed four-cell AA battery holder. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.

Will this match everything shown in the photo?

The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.

Does four-cell mean the holder supplies a particular voltage?

No. The printed arrangement does not supply contacts or determine how cells are connected. Output depends on the cells and wiring in your separately designed circuit; no electrical output is supplied by this item.

Can I design the enclosure using only the listed dimensions?

Use them for an initial space estimate only. A finished assembly also needs clearance for the cells, separately selected contacts, wire routing, mounting, and the motion required to replace the cells.

Is this intended as a loose-cell travel box?

The listing describes a project holder, not a closed transport case. If you need to carry spare cells, choose a storage arrangement designed to keep them contained and their terminals appropriately separated during transport.

Original design: hargo — AA Battery Holder. MakerWorld model 1643040. Original design

Your cart

Ordering within Canada? Buy each product through its secure checkout, or ask us about combining parts into one order.

Your cart is empty. Find a useful part and add it here.