Creator design reference for 10-inch Rack Cable Brush Panel — Printed Frame; included printed parts are specified in the listing.Design reference photo

Creator photo; included parts are listed below. Accessories not included.

Electronics & racks / Parts for your next project

10-inch Rack Cable Brush Panel — Printed Frame

3D printed in PETG for organizing cable pass-throughs in a compatible 1U rack space.

$34.99 CAD

Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.

Check fit before ordering ↓

A closer look

3D printed in PETG for organizing cable pass-throughs in a compatible 1U rack space. Includes one printed 10-inch 1U panel frame. Hardware, devices, accessories shown and installation are not included. Brush strip is not included.

Check the fit

Start with these details so you can choose the right part for your setup.

  • Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.

What’s included

  • One printed 10-inch 1U panel frame.
  • Hardware, devices, accessories shown and installation are not included. Brush strip is not included.

Give rack cables a planned pass-through position

A cable pass-through panel can make the front of a small rack easier to organize by giving leads a defined route between areas. This printed frame is intended for a compatible 10-inch, 1U rack position and can be considered while laying out a compact network or electronics project. Choose a location that makes sense for the equipment on both sides of the panel, with room to identify and reach the cables later. Keep the route convenient for the largest plugs you expect to move through it. A tidy layout works best when connections remain accessible, rather than being hidden behind a tightly packed bundle.

Measure the rack and plan the separate brush strip

The frame measures approximately 252 × 42 × 9.25 mm as an individual printed component. Those outer dimensions do not specify the pass-through opening or confirm a mounting-hole match with every compact rack. Compare the rail spacing, fastener positions and available clearance in the intended rack. This listing supplies the printed frame without a brush strip. If your installation will use a strip, confirm its mounting profile, length and fit with the frame before purchasing it separately. Also allow for the cable bundle and any connector that needs to pass through the completed arrangement; a cable fitting comfortably does not mean its plug will fit the same opening.

Keep the cable route easy to change

Lay out the cables before fastening the panel so you can identify routes that cross unnecessarily or pull tightly at the equipment. Leave reasonable service slack and observe the cable maker's bend guidance. Support cable weight using the appropriate parts elsewhere in the rack rather than treating the panel opening as a clamp. When changing a connection, guide the connector through deliberately instead of pulling on the lead. Periodically check the opening and any added brush strip for trapped debris or a cable rubbing against an edge. The frame is an organization accessory and does not establish a sealed, weatherproof or fire-rated barrier across the rack opening.

Product questions

What does the listed price include?

One printed 10-inch 1U panel frame. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Hardware, devices, accessories shown and installation are not included. Brush strip is not included.

Will this match everything shown in the photo?

The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.

Is this a complete panel with bristles already installed?

No. The listing supplies the printed frame only. A brush strip is separate and needs to be selected for a compatible fit with the frame.

Should I measure the cable or its connector before ordering?

Check both. The cable bundle needs routing space, while any plug that will pass through the panel needs adequate clearance through the finished opening.

Will this fit a standard full-width 19-inch rack?

This version is intended for a compatible 10-inch rack position. Do not assume its width or mounting points match a 19-inch rack arrangement.

Original design: BKG — 10 inch Rack Brush Panel – 1U - LAB RAX. MakerWorld model 1546022. Original design

Your cart

Ordering within Canada? Buy each product through its secure checkout, or ask us about combining parts into one order.

Your cart is empty. Find a useful part and add it here.