Design reference photoCreator photo; included parts are listed below. Accessories not included.
LiPo Balance Connector Cap Assortment
3D printed in TPU for covering unplugged balance connectors during storage.
Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Secure checkout for Canadian shipping addresses. Choose your quantity on Stripe. Shipping to the U.S.? Contact us for a shipping quote before ordering. U.S. shipping is an additional charge.
Check fit before ordering ↓A closer look
3D printed in TPU for covering unplugged balance connectors during storage. Includes five printed caps: one each for 2S, 3S, 4S, 5S and 6S connector sizes. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Check the fit
Start with these details so you can choose the right part for your setup.
- Confirm your board, connector or rack dimensions and mounting-hole pattern before ordering.
What’s included
- Five printed caps: one each for 2S, 3S, 4S, 5S and 6S connector sizes.
- Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Sort storage covers by the connectors you use
This assortment is useful for a hobby workspace with several unplugged balance-connector sizes. Establish which of the 2S through 6S versions match the connectors already in your equipment, then keep each cap associated with its intended size. A small organized compartment for unused caps makes them easier to retrieve when a pack or lead is put away. The practical benefit is a consistent physical covering routine during storage, with a particular cover selected for the connector instead of an improvised loose wrapping.
Compare housing shape as well as the size name
Count and inspect the actual connector positions, then compare the plastic housing profile, latch features and cable exit. A size designation alone does not describe every connector family. The printed caps vary in length across the assortment, while the listed individual bounds share an approximately 8.6 by 8 mm cross-section. Those outside measurements do not establish the internal fit of your connector. Provide an end view and a side view if you need help comparing the shape, and identify the connector rather than only the battery brand.
Fit the cap without pulling on the wires
Work with the connector unplugged from its mating equipment as intended for storage, following the equipment's own handling guidance. Hold the connector housing when placing or removing the cap so the small wires do not become handles. The TPU material is specified for these printed pieces, but flexibility is not a reason to stretch a mismatched cap over an unsuitable housing. Check that the selected part sits naturally and does not press the leads into an awkward bend or hide damage that needs attention.
Keep the full battery storage routine intact
A printed cap covers a connector physically; it does not change the state of the battery or replace the storage instructions for the pack and charging equipment. Keep required labels visible and continue to use an appropriate battery-storage arrangement. Inspect caps for dirt or damage before putting them back on a connector, and keep loose conductive items away from the equipment according to its instructions. If the connector or battery type changes, repeat the identification and fit check rather than relying on the size of the previous cap.
Product questions
What does the listed price include?
Five printed caps: one each for 2S, 3S, 4S, 5S and 6S connector sizes. Shipping within Canada is included in the listed price. Applicable taxes are calculated at checkout. Electronics, batteries, metal contacts, fasteners, accessories shown and installation are not included.
Will this match everything shown in the photo?
The creator photo is a design reference and may show other variants, quantities or accessories. The included-parts list describes exactly what this listing supplies.
Can I select a cap only from the battery's cell count?
Use the cell-count designation as a starting reference, then compare the actual balance-connector housing and pin arrangement. Different connector details can prevent a match even when the size label looks appropriate.
Does a fitted cap disconnect the battery internally?
No. It is a physical storage cover and supplies no electrical switching or protection function. Follow the battery maker's handling and storage instructions independently of the cap.
How should I remove a snug cap?
Hold the connector housing and remove the cap by the intended fit direction without pulling on individual wires. If removal requires excessive force, stop and reassess whether the selected cap matches the housing.
Original design: Grollaz — Lipo 2-3-4-5-6 S Balancing Caps. MakerWorld model 1240796. Original design